Amana GUC Series Bedienerhandbuch Seite 4
- Seite / 28
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4
LOCATION
• Centralize the furnace as is practical with respect to
the air distribution system.
• The furnace must be set on a level floor to enable the
condensate produced to drain properly. If the floor may
become wet or damp at times, the furnace should be
supported above the floor on a concrete base sized
approximately 1-1/2” larger than the base of the fur-
nace.
• Do not install the furnace directly on carpeting, tile, or
combustible material other than wood flooring.
• Do not install the furnace where the combustion air is
exposed to the following substances:
permanent wave solutions
chlorinated waxes or cleaners
chlorine based swimming pool chemicals
water softening chemicals
deicing salts or chemicals
carbon tetrachloride
halogen-type refrigerants
cleaning solutions (such as perchloroethylene)
printing inks
paint removers
varnishes
hydrochloric acid
cements and glues
antistatic fabric softeners for clothes dryers
and masonry acid washing materials.
Exposure to contaminated combustion air will result in
safety and performance-related problems.
• If the furnace is installed in a residential garage, the
furnace must be positioned so that the burners and
ignition source are located not less than 18 inches
(457 mm) above the floor and protected from physical
damage by vehicles.
II. General Information
WARNING
Possible death, personal injury or property
damage due to fire, explosion, smoke, soot,
condensation, electrical shock or carbon
monoxide may result from improper
installation, repair, operation, or
maintenance on this product.
WARNING
To prevent death, personal injury or
property damage due to fire, do not install
this furnace in a mobile home, trailer, or
recreational vehicle.
To ensure safe and efficient operation, install, operate,
and maintain this upflow furnace in accordance with these
installation and operating instructions, all local building
codes and ordinances, or with the latest edition of the
National Fuel Gas Code, NFPA 54/ANSI Z223.1*, and/or
CAN/CGA B149 Installation Codes, local plumbing or
waste water codes and other applicable local codes.
The rated heating capacity of the furnace should be
greater than or equal to the total heat loss of the area to be
heated. The total heat loss should be calculated by an
approved method or in accordance with “A.S.H.R.A.E.
Guide” or “Manual J-Load Calculations” published by the
Air Conditioning Contractors of America.
*Obtain from: American National Standards Institute 1430
Broadway, New York, NY 10018.
TRANSPORTATION DAMAGE
All furnaces are securely packed in shipping containers
tested according to the International Safe Transit Associa-
tion standards. The carton must be checked upon arrival
for external damage. If damage is found, a request for
inspection by carrier’s agent must be made in writing
immediately.
The furnace must be carefully inspected on arrival for
damage and bolts or screws which may have come loose
in transit. In the event of damage the consignee should:
1. Make a notation on delivery receipt of any visible
damage to shipment or container.
2. Notify carrier promptly and request an inspection.
3. With concealed damage, carrier must be notified as
soon as possible - preferably within five days.
4. File the claim with the following support documents
within a nine month statute of limitations.
• Original or certified copy of the Bill of Lading, or
indemnity bond.
• Original paid freight bill or indemnity in lieu thereof.
• Original or certified copy of the invoice, showing
trade and other discounts or reductions.
• Copy of the inspection report issued by carrier’s
representative at the time damage is reported to
carrier.
The carrier is responsible for making prompt inspection of
damage and for a thorough investigation of each claim.
The distributor or manufacturer will not accept claims from
dealers for transportation damage.
EXISTING FURNACE REMOVAL
Note
:
When an existing furnace is removed from a
venting system serving other appliances,
the venting
system may be too large to properly vent the remaining
attached appliances.
The following steps shall be followed with each appliance
remaining connected to the common venting system placed
in operation, while the other appliances remaining con-
nected to the common venting system are not in operation.
(a) Seal any unused openings in the common venting
system.
(b) Visually inspect the venting system for proper size
and horizontal pitch and determine there is no block-
- GUX-X, GUC-X, & GUD-X 1
- Installation Instructions 1
- To The Owner 2
- To The Installer 2
- I. Safety and Unit Location 3
- II. General Information 4
- III. Air Requirements 5
- Materials 7
- (One Pipe Installations) 8
- (GUD - Two Pipe) 9
- TERMINATIONS 10
- VENT PIPE INSTALLATION 12
- Inside Feet of Straight Pipe 13
- Inlet Gas Pressure 14
- NATURAL GAS CONNECTION 15
- The orientation of the 15
- GAS PIPING CHECKS 16
- PROPANE GAS PIPING CHARTS 17
- IX. Electrical Wiring 18
- Control Module 19
- Flame Roll-Out 21
- Protection Device 21
- GUD MANIFOLD PRESSURE 24
- CHECK MAIN BURNER FLAMES 24
- Check the burner flames for: 25
- 1. Good adjustment 25
- 2. Stable, soft and blue 25
- XIII. Maintenance 26
- XIV. Functional Parts List 28
Panasonic TXL42E5E Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Audio Panasonic TXL42E5E.
Wir stellen 1 PDF-Handbücher Panasonic TXL42E5E zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Kommentare zu diesen Handbüchern