Amana GCI Technical Information PDF herunterladen (Seite 10)

FURNACE SPECIFICATIONS

10 Rev. 1

1. These furnaces are manufactured for natural gas operation. Optional kits are available for conversion to propane

gas operation.

2. For elevations above 2000 feet the rating should be reduced by 4% for each 1000 feet above sea level. The furnace

must not be derated, orifice changes should only be made if necessary for altitude.

3. The total heat loss from the structure as expressed in TOTAL BTU/HR must be calculated by the manufacturers

method in accordance with the "A.S.H.R.A.E. GUIDE" or "MANUAL J-LOAD CALCULATIONS" published by the

AIR CONDITIONING CONTRACTORS OF AMERICA. The total heat loss calculated should be equal to or less

than the heating capacity. Output based on D.O.E. test procedures, steady state efficiency times output.

4. Minimum Circuit Ampacity calculated as: (1.25 x Circulator Blower Amps) + I.D. Blower Amps.

MODEL

GUIC045CA30

GUIC045CX30

GUIC045DA30

GUIC045DX30

GUIC070CA30

GUIC070CX30

GUIC070DA30

GUIC070DX30

GUIC070CA40

GUIC070CX40

GUIC070DA40

GUIC070DX40

GUIC090CA30

GUIC090CX30

GUIC090DA30

GUIC090DX30

GUIC090CA50

GUIC090CX50

GUIC090DA50

GUIC090DX50

GUIC115CA40

GUIC115CX40

GUIC115DA40

GUIC115CA50

GUIC115CX50

GUIC115DA50

GUIC115DX50

GUIC140CA50

GUIC140CX50

GUIC140DA50

Btuh Input (US) 46,000 69,000 69,000 92,000 92,000 115,000 115,000 140,000

Output (US) 36,800 55,200 55,200 73,600 73,600 92,000 92,000 110,400

A.F.U.E. 80% 80% 80% 80% 80% 80% 80% 80%

Rated External Static (" w.c.) .10 - .50 .12 - .50 .12 - .50 .15 - .50 .15 - .50 .20 - .50 .20 - .50 .20 - .50

Temperature Rise (°F) 35 - 65 35 - 65 35 - 65 40 - 70 40 - 70 40 - 70 40 - 70 45 - 75

Pressure Switch Trip Point (" w.c.) -0.55 -0.55 -0.55 -0.55 -0.55 -0.55 -0.55 -0.55

Blower Wheel (D" x W") 9 x 8 9 x 8 10 x 6 10 x 8 10 x 8 10 x 7 10 x 9 10 x 9

Blower Horsepower 1/3 1/3 1/2 1/2 1/2 1/2 3/4 3/4

Blower Speeds 44444444

Max CFM @ 0.5 E.S.P. 1200 1290 1450 1380 1980 1590 1985 2050

Power Supply 115-60-1 115-60-1 115-60-1 115-60-1 115-60-1 115-60-1 115-60-1 115-60-1

Minimum Circuit Ampacity (MCA) 8.6 8.5 10.4 8.2 14.6 13.1 13.7 14.6

Maximum Overcurrent Device 15 15 15 15 15 15 15 15

Transformer (VA) 40 40 40 40 40 40 40 40

Heat Anticipator 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7

Primary Limit Setting (°F) 230 220 170 170 or *150 170 or *160 170 or *150 190 or *180 135

Auxiliary Limit Setting (°F) 160 160 160 160 160 160 160 160

Rollout Limit Setting (°F) 275 300 300 300 300 350 350 325

Fan Delay On 30 secs. 30 secs. 30 secs. 30 secs. 30 secs. 30 secs. 30 secs. 30 secs.

Off Heating * 90 secs. 90 secs. 90 secs. 90 secs. 90 secs. 90 secs. 90 secs. 90 secs.

Off Cooling 45 secs. 45 secs. 45 secs. 45 secs. 45 secs. 45 secs. 45 secs. 45 secs.

Gas Supply Pressure (Natural/Propane) ("w.c.) 7 / 11 7 / 11 7 / 11 7 / 11 7 / 11 7 / 11 7 / 11 7 / 11

Manifold Pressure (Natural/Propane) ("w.c.) 3.5 / 10 3.5 / 10 3.5 / 10 3.5 / 10 3.5 / 10 3.5 / 10 3.5 / 10 3.5 / 10

Orifice Size (Natural/Propane) #43 / #55 #43 / #55 #43 / #55 #43 / #55 #43 / #55 #43 / #55 #43 / #55 #43 / #55

Number of Burners 23344556

Vent Connector Diameter (inches) 44444444

Shipping Weight (lbs.) 140 151 152 169 178 190 194 198

*150 = The GUIC115**40 furnaces can also use primary limit part #10728332 in place of limit part #10728319 but without limit baffle part #11094802.

*180 = The GUIC115**50 furnaces can also use primary limit part #10728334 in place of limit part #10728304 but without limit baffle part #11094802.

* Off Heating - This fan delay timing is adjustable (60, 90, 120 or 180 seconds), 90 seconds as shipped.

*150 = The GUIC090**30 furnaces can also use primary limit part #10728332 in place of limit part #10728319 but without limit baffle part #11094802.

*160 = The GUIC090**50 furnaces can also use primary limit part #10728331 in place of limit part #10728304 but without limit baffle part #11094802.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 21 22

Kommentare zu diesen Handbüchern

Keine Kommentare

Amana GCI Technical Information Seite 10

Kommentare zu diesen Handbüchern