Amana ACM2160A Bedienungsanleitung PDF herunterladen

Proper installation is the installer's responsibility!

Write the model & serial numbers on the owner's manual.

The model number label is located on the oven front.

UL Listed-For use over electric heat source

models

(Wall Ovens)

•

27" : AOES2730, AOCS2740,

MEW5527DD, MEW6527DD

30" : AOES3030, AOCS3040,

MEW5530DD, MEW6530DD,

AEW3530DD, AEW4530DD,

JJW8130DD, JJW9130DD

WARNING

To avoid risk of electrical shock, personal injury, or

death, disconnect power to wall outlet before beginning

installation.

Parts, Tools, and Materials

The following parts are supplied with the oven:

Tools required to perform installation:

• Phillips Screwdriver

• Saw (Electric or Hand)

• Drill with

/16" and

/64" drill bits (Electric or Hand)

• Tape Measure

• Pencil

• Framing Square

• Level

Shipping Weight

• Approximate shipping weight is 16 lbs.

Cutout Dimensions

Dimensions 27" 30"

Height 16 3/4"

16 3/4"

Width 25 1/2" 25 1/2"

Depth (min.) 23 3/4" 23 3/4"

WARNING

To avoid risk of electrical shock, personal injury, or

death:

• Before drilling into the wall, note where electrical

outlets are and where electrical wire might be

concealed behind the wall. YOU COULD GET AN

ELECTRICAL SHOCK if you contact electrical wire

with the drill bit.

• Locate and disconnect the power to any electrical

circuits that could be affected by installing this oven.

IF YOU DO NOT DISCONNECT THE POWER, YOU

COULD GET AN ELECTRICAL SHOCK.

CAUTION

To avoid personal injury, wear gloves when handling the

metal parts. Parts are sharp and can cause cuts and

abrasions.

FTK-127/130 Built-In Trim Kit Installation Instructions

For use with the following microwave oven ACM2160A and UMC5200AA

Trim Frame (1)

Upper Duct (1)

Bottom Bracket (1)

Side Duct (1)

Anti-Tip Bracket (1)

1/2" Screws

(11 required, 2 extra)

1" Screws

(4 required, 2 extra)

Template (1)

Bottom Duct (1)

3" min.

Width

Height

Depth

Electric Heat Source Model

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Parts, Tools, and Materials

1Proper installation is the installer's responsibility!Write the model & serial numbers on the owner's manual.The model number label is

Seite 2 - Properly polarized

2Electrical rating of this oven:• 120 VAC @ 60 Hz• 13 A / 1100 W• You need a DEDICATED 120 VAC, 60 Hz, 20 A, fused electrical supply (located in the c

Seite 3 - 1/2" screws

3Installation of Bottom Bracket1. Disconnect power from microwave oven beforeproceeding with installation.2. Remove any loose items from inside the mi

Seite 4 - Trim kit is completed

Mounting Trim Frame1. Position trim frame over the microwave oven.2. Verify trim frame is level and the microwave oven iscentered within the trim fram

Seite 5 - ATTENTION

1FTK-127/130 Instructions d’installation du kit finitions encastréesPour utilisation avec les fours à micro-ondes suivants ACM2160A and UMC5200AAL’uti

Seite 6

2Spécifications électriques de ce four :• 120 VAC @ 60 Hz• 13 A / 1100 W• Contrôlez avec un électricien qualifié si vous n’êtes passûr si le

Seite 7 - Plaque anti-basculement

3Languettesparoi latéraleparoi supérieure VisPlan découpéAvant ArrièreVis 1/2 poPlaque anti-basculementInstallation du support inférieur1. Débranche

Seite 8

3-1/8 po19-1/8 po29-3/4 po2-7/8 po3-1/8 po19-1/8 po26-7/8 po1-7/16 poChâssis – 27 po Châssis – 30 poParoi inférieure Support inférieurPlaque anti-basc